Moore's Sewing, Vacuum and FanMoore's Sewing, Vacuum and Fan

Customer Service: 1-800-865-9664

Monthly Archives: January 2014

  • Using a Brother Scan N Cut to Cut Fabric for Hand Applique

    January 7, 2014
    100_7555

    I like doing hand applique, but I do not enjoy tracing and cutting out the fabric pieces. With a Scan N Cut you can skip the tracing and let the machine do the cutting for you. I'm going to show you how to add a seam allowance to your applique shapes for handwork and to make the Scan N Cut do the cutting for you.

    Supplies: Quilt fabric Heavy spray starch Scan N Cut machine Low tack mat Regular tack mat with the extra-sticky mat on it Applique shapes printed at full size on paper

    Instructions:

    100_7522 1. Set desired seam allowance by pressing the wrench button.100_7523 2. On page 3 selected your desired seam allowance and click the OK button.100_7536 3. Place paper pattern on the low tack mat.100_7533 4. Load low tack mat with attached paper pattern by pressing the load mat button.100_7534 5. Press Scan icon.

    100_7535 6. Press Scan to Cut Data icon. Press Start/Stop button to scan. Wait for the scan to be processed. 7. Unload mat by pressing the same button you pressed to load the mat.100_7541 8. Crop the image, if necessary, and press SAVE button.100_7542 9. You will be offered options to save the scanned image to a USB stick or the Scan N Cut internal memory.

    100_7547 10. You wind up back at the cropping/save screen which is a little confusing. Use the return button 'U turn' arrow in upper right corner to proceed. Click on OK to delete scanned data.

    100_7549 11. Use the return button in the next screen to get to the Pattern or Scan screen.100_7551 12.  Press the Pattern button,

    100_7552 13. Press the Saved Data button.100_7553 14. Now it is time to retrieve a previously saved image. Press the button that corresponds to where the image was saved. You may need to page down to find the image with the pieces you want to cut.100_7554 15. Select the image and press OK.100_7525 16. To put a seam allowance around one or more pieces in an image, select top left icon.

    100_7526 17. Select a shape you want to add seam allowance to . A red box will appear around the selected shape. Press the button at the right end of the  middle row.100_7527 18. The button on bottom left will add the seam allowance to the selected piece.100_7528 19. Seam allowance has been added.100_7530 20. Repeat with each shape. When all the shapes that you need have a seam allowance, press OK.

    100_7500 21. Starch the fabric with heavy spray starch. This will give the fabric more body and produce better cutting results. Place fabric on extra sticky mat. Load the mat with the fabric. Note in the photo above that there are several pieces of fabric on the mat. The pieces I need for this small project will be arranged below to be cut from the proper color in a single cutting session rather than a separate cutting session for each color.

    100_7531 22. Press the scan button located near the bottom left corner of screen. 23. You will be able to see the scan of your fabric, allowing you to move each piece to where you want to cut out your applique shape. Click on the OK button100_7515 24. If you want the original shape to be drawn on the fabric use either the water soluble or air erasable fabric pen in the white pen holder. 25. If you want to draw, press the DRAW key.100_7514 26. If necessary, replace the white pen holder with the blue blade holder and set it according to instructions in the manual.100_7540 27. Press the CUT button.

    100_7502 28. Remove fabric from mat. For this design, it is easier to remove the large fabric pieces first, leaving the shapes that are part of the finished project rather than trying to pick the shapes out leaving the surrounding fabric.

    Pdf image

     

1 Item(s)